JN0-661 Juniper Routing and Switching Services Exam Questions

Juniper Service Provider Routing and Switching JN0-661 exam is an ultimate source to boost your career. The Juniper JN0-661 exam dumps material is strictly designed by the subject matter experts, after an in-depth analysis of Juniper recommended material. The Juniper JN0-661 JNCIS-SP exam increases your ability in various domains, such as Route summarization and route leaking, Policers, including tricolor marking and hierarchical policers and Given a scenario, demonstrate knowledge of how to configure and monitor IGMP, PIM-DM, PIM-SM (including SSM) and MSDP. We at OnlineExamDumps provide you latest JN0-661 exam questions. A candidate will be allocated 90 minutes to complete the exam and its important for them to must score 70% marks.

Version: 8.0
Question: 1

Click the Exhibit button.

Referring to the exhibit you have configured an L2 circuit that connects Site-1 and Site-2, but the L2 circuit is not functioning The topology in this scenario is shown below.
Site-1 > PE-1 > P-1 > P-2 > PE-2 Site-2
Which action will allow communication between Site-1 and Site-2?

A. Change the virtual circuit identifier to 2 for PE-2.
B. Add the family in the statement under the age-0/0/1.512 interface for PE-1 and PE-2.
C. Add the lo0 interface under the {edit protocols Idp} hierarchy for all routers.
D. Add the lo0 interface under the {edit protocols 12circuit} hierarchy for PE-1 and PE-2

Answer: C

Question: 2

Which command will match communities 101:111,111:1, and 999:1111?

A. set policy-options community COMMUNITY members “^…:1?”
B. set policy-options community COMMUNITY members “^1.*:1+”
C. set policy-options community COMMUNrTY members [“^1.1:1?” 999:1111]
D. set policy-options community COMMUNITY members “^…:1+”

Answer: D

Question: 3

New Updated JN0-661 Exam Questions JN0-661 PDF dumps JN0-661 practice exam dumps: https://www.dumpsschool.com/JN0-661-exam-dumps.html (132 Questions)

Click the Exhibit button

Referring to the exhibit, you have configured an L3VPN that connects Site-1 and Site-2 together, but the BGP routes are being hidden on the PE routers. The topology in this scenario is shown below.
Site-1 > PE-1 > P-1 > P-2 > PE-2 > Site-2
Which two acttions would allow communication Site-1 and Site-2? (Choose two.)

A. Disable CSPF on under MPLS on P-1 and P-2.
B. Configure DGP on P-1 and P-2.
C. Enable RSVP for all interfaces on P-1 and P-2.
D. Enable LDP for all interfaces on all routers.

Answer: C, D

Question: 4

A layer 2 circuit (RFC 4447) is established between two PE routers to provide connectivity between two customer sites. Which two statements related to this deployment are true?

A. Kompella encapsulation is used in the data plane communications.
B. LDP must be used for the control plane communications
C. BGP must be used for the control plane communications.
D. Martini encapsulation is used in the data plane communications.

Answer: B, D

Question: 5

Click the exhibit button

Referring to the exhibit, which router will be the RP?

A. R4 for all groups
B. R1 for group 224.1.1.11 and R4 for all other groups
C. R1 for all groups
D. R4 for group 224.1.1.12 and R1 for all other groups

Answer: A

Question: 6

Click the Exhibit button

You must ensure that r1’s IPv4 loopback address exists in r3’s inet 0 routing table
Referring to the exhibit, which statement is true?

A. An IPv4 unicast realm can be enabled on each router.
B. A policy can be configured on M to redistribute 172.16.100.1/32 into OSPFv2, which would cause r3 to eventually learn the route and place it into inet0.
C. A RIB group can be configured on r3 to copy that route into inet 0 because 172.16.100.1/32 exists in r3’s inet6.0 table
D. A policy can be configured on r1 to redistribute 172 16 100 1/32 into OSPFv3, which would cause r3 to eventually learn the route and place it into inet 0.

Answer: C

Facebook Comments